ANAVI Macro Pad 8 Maker Kit Assembly Guide

In a previous update we shared the exact steps how to assemble ANAVI Macro Pad 8 Developer Kit. Now let’s have a look at the Maker Kit.

ANAVI Macro Pad 8 Maker Kit Soldering and Assembly Video Tutorial

The maker kit provides the printed circuit board (PCB) and an addressable LED strip. There are also some nice stickers. Other accessories have to be purchased separately. You can use any mechanical switches compatible with Cherry MX plate footprint and 3mm LEDs.

ANAVI Macro Pad 8 Maker Kit Unboxing

Furthermore with the maker kit you can perform a hot-swap upgrade of ANAVI Macro 8. It requires a very specific procedure which was explained in a previous article. If you have this in mind don’t solder anything and have a look at the other video tutorial.

Required tools for soldering of ANAVI Macro Pad 8 Maker Kit

The assembly of ANAVI Macro Pad 8 Maker Kit requires soldering and advanced skills. The following tools are required:

  • Soldering iron
  • Scissors
  • Optionally: screwdriver, tweezers and a keycap puller

It is also a good idea to stay safe and get a smoke absorber while soldering, for example our open source ANAVI Fume Extractor.

Please have a look at the video and follow the steps below if you have ANAVI Macro Pad 8 Maker Kit.

Solder mechanical switches to the PCB

Any type of mechanical switch compatible with Cherry MX plate footprint is suitable for ANAVI Macro Pad 8. The developer kit comes with Gateron mechanical switches. The maker kit allow you to use different brand and color.

Choosing the most appropriate switch for your needs and taste is a matter of personal preference. There are many different brands and colors. For example, the blue mechanical switches are more noisy which could be sometimes fun but also annoying during daily work. The red switches are fast and not very noisy therefore they are often proffered by gamers.

There are two pins on each mechanical switch that must be soldered to the printed circuit board. That makes 16 pins in total. The position of the each pin is very specific and the switch goes into the PCB. One of the pins is for the signal coming from the Microchip ATmega32U4 microcontroller, the other pin is for ground.

Solder 3mm LED

This step is actually optional depending on the the type of the mechanical switch. Some mechanical switches may not have a hole in the plastic enclosure for a 3mm LED.

Each 3mm LED for through-hole soldering has 2 legs. The longer leg is the positive terminal, also known as anode. The shorter leg is negative and also known as cathode.

The shorter leg that indicates the negative terminal must go into the square hole of the PCB. ANAVI Macro Pad 8 has 8 mechanical switches therefore 8 LEDs are required. If you want you can use different color of the LEDs. You can even mix colors.

Solder WS2812B addressable LED strip to the back of the PCB

Using scissors cut a little bit from both ends of the LED strip to make sure it will stretched when placed on the board. However it is tricky, be careful and make sure enough from the pads are available to make a good contact after soldering them.

It is very important to properly set the direction of the WS2812B LED strip. On the LED strip you will notice small arrows indicating the direction. They should point from the microUSB connector towards the other end of the PCB as shown in the video.

If you have successfully completed these 3 steps your ANAVI Macro Pad 8 should look just like a developer kit having all accessories soldered. Therefore the next steps are the same as for both the developer and the maker kit. Explore them at our previous blog post as well as in the user’s manual.

Thank you for using ANAVI Macro Pad 8 and for supporting this entirely open source project!

Getting Started with QMK Firmware

Out of the box, all kits of ANAVI Macro Pad 8 are powered by the popular open source QMK firmware.

ANAVI Macro Pad 8
ANAVI Macro Pad 8

QMK stands for Quantum Mechanical Keyboard and it is an open source community centered around developing various computer input devices. The project is hosted in GitHub. More than 1700 developers contributed to this open source firmware over the years. QMK supports more than 2000 keyboards and keypads brands.

Although QMK is very powerful and flexible, it might be a challenge to get used to it if you haven’t used it before. Over the next weeks and months, as part of efforts for increasing the documentation related to ANAVI Macro Pad 8, we will be rolling out updates related to QMK.

QMK Configurator loaded in a web browser with the default keymap for ANAVI Macro Pad 8

QMK offers several options to select, customize and flash a keymap for your keyboard:

  • Command-line interface – advanced but not very user friendly
  • QMK Toolbox – application for MacOS and Windows users
  • QMK Configurator – an online tool used for easily creating firmware files for keyboards supported by QMK.

You can use QMK on MS Windows, MacOS and GNU/Linux distributions. To get started with the QMK firmware please explore this tutorial from the official documentation and install all required software suitable for the operating system on your PC.

Keymaps for ANAVI Macro Pad 8

The QMK source code for ANAVI Macro Pad 8 is available as part of the main repository in GitHub. So far there are 5 keymaps available:

  • Default – with 2 layers for demo purposes
  • KiCad – free software suite for electronic design automation which as used to design ANAVI Macro Pad 8,
  • Kodi – for the free and open source media player application,
  • OBS – for the popular open source video recording and live streaming software,
  • Zoom – for the popular video communication software.

Over the time we plan to extend the list with keymaps for other popular software applications. Please feel free to submit your favorite keymaps for ANAVI Macro Pad 8 to the QMK repository in GitHub!

Compile QMK for ANAVI Macro Pad 8

After installing QMK software on your computer, from the command line you can compile QMK firmware with the default keymap for ANAVI Macro Pad 8 using the following command:

qmk compile -kb anavi/macropad8 -km default

Flash QMK on ANAVI Macro Pad 8

Follow the steps below to flash the compiled QMK firmware to ANAVI Macro Pad 8:

  • Connect ANAVI Macro Pad 8 to your personal computer with USB to micro USB cable
  • Execute the following command in a terminal to flash the default keymap:
qmk flash -kb anavi/macropad8 -km default
  • Press the RESET button on ANAVI Macro Pad 8 when asked:
Detecting USB port, reset your controller now.....
  • Wait until the firmware flashes successfully:
avrdude done.  Thank you.

The heart of ANAVI Macro Pad 8 is Microchip ATmega32U4. It is an 8-bit microcontroller part of the AVR family. QMK relies on avrdude as the utility to download, upload and manipulate the firmware of these microcontroller.

Microchip ATmega32u4
Microchip ATmega32u4 on ANAVI Macro Pad 8

ANAVI Macro Pad 8 is available at our distributors Crowd Supply and Mouser. Please contact us if you are interested in wholesale orders or if you prefer shipping directly from the EU.

ANAVI Macro Pad 8 Developer Kit Assembly Guide

Please have a look at the video and follow the steps below to assemble ANAVI Macro Pad 8 Developer kit. Although you can do it with your bare hands, simple tools like a screwdriver, tweezers and a keycap puller might be useful.

ANAVI Macro Pad 8 developer kit comes with 8 Gateron mechanical switches and red leds. If you prefer another type of switches or color of the LEDs, please have a look at the Maker kit which requires soldering but allows to use different Cherry MX compatible switches or even make a hot-swap upgrade.

Step 1: Stickers

The first step optional. Each kit includes a set stickers. Feel free to add them to the translucent keycaps included in ANAVI Macro Pad 8 developer kit. You can do it with your bare hand or eventually with the help of tweezers.

You can place a sticker on the top or on the side of the keycap. If you like retro electronics you may find some similarities in this approach to the famous keyboard of the best selling personal computer of the 20th century Commodore 64.

ANAVI Macro Pad 8 is powered by the popular open source firmware QMK which allows you to create various layouts. You can make a keymap with 2 or more layouts. A sticker on the side of the keycap might be useful as a visual aid to indicate the additional function of the key.

Step 2: Keycaps

Place all keycaps on 8 mechanical switches of ANAVI Macro Pad 8. You can easily do this with your bare hands. It takes just a few seconds.

As you can see in the video a keycap puller might be useful if you make a mistake and want to pull off a keycap and place it on another location.

Step 3: Peel Off Protective Films from the Acrylic Enclosure

Peel off the protective films from both sides of the two laser cut transparent acrylic parts. The removal of the protective films is quite annoying but once you get rid of them, the acrylic enclosure will be crystal clear and fully transparent.

Step 4: Assemble the Acrylic Enclosure

Assemble the acrylic enclosures. In the cardboard box you also will find M3 black plastic screws, nuts and standoffs. Although you can assemble them with your bare hands a screw driver might be handy.

First place 4 of stand-offs with screws to the bottom acrylic part. After that place ANAVI Macro Pad 8 on top of them. The printed circuit board has 4 mounting holes for this purpose.

Add the rest of stand-offs on top of ANAVI Macro Pad 8 to secure the printed circuit board to the bottom part as shown in the video. Place the top acrylic part and fasten it with the 4 M3 nuts. Finally add the silicon protective pads on the screws on the bottom.

Step 5: Mini OLED Display

Step number 5 is optional. The default open source QMK firmware for ANAVI Macro Pad 8 support mini OLED display connected over the communication bus I2C.

By default mini display in yellow-blue 0.96″ I2C OLED. It comes with 4 jumper wires which might be useful for debugging purposes or if you plan to make a custom 3D printed case. However for the default acrylic enclosure the wires are not needed.

Peel off the protected film and place the mini OLED display as shown in the video to ANAVI Macro Pad 8. Pay attention to the labels that indicated the pin connectors of the display. They must match the labels on the keyboard.

Step 6: Turn On ANAVI Macro Pad 8

Gently plug a USB to microUSB cable to connect ANAVI Macro Pad 8 to a personal computer. Please be careful with the microUSB connector because a harsh bending of the USB cable may damage the microUSB connector.

Thanks to the QMK firmware ANAVI Macro Pad 8 will be detected as human interface device and should work out of the box. Furthermore with QMK you have the freedom to fully customize each key.

ANAVI Macro Pad 8
ANAVI Macro Pad 8

Please note that a USB to microUSB cable is not included in any of the kits. Reuse a cable from an old electronic device or purchase a cable according to your taste. Make sure that the cable supports both power and data transfer over USB.

Thank you for supporting and using our open source kits. Stay tuned for more updates, including details for soldering ANAVI Macro Pad 8 Maker kit.

Update Home Assistant

Home Assistant is a popular open source platform for home automation. The installation is still tricky and a bit annoying but the nowadays updates are straight-forward and super easy. This article and short video tutorial provide the exact steps how to update Home Assistant operating system and core following the best practices.

How to update Home Assistant?

Updates bring new features, bug fixes and security improvements. Home Assistant is a platform focused on privacy. There are regular updates. If are following the blog posts and the social media accounts you can often read news about critical security updates. It is recommended to install them as soon as possible.

Step 1: backup the existing Home Assistant installation by creating a snapshot of the whole system. From the left menu go to Supervisor. Click the Snapshots tab. Select full snapshot for type and optionally set a name. Click the CREATE button. Wait for a moment until the snapshot is ready.

Step 2: read the releases notes for breaking changes coming with the latest stable version. From the left menu go to Supervisor. Click RELEASE NOTES for any available updates. Check all release notes between the version you are running at the moment and the one you are upgrading to. Use the search function in your web browser to locate the chapter for Breaking Changes.

Step 3: check your configuration. This can be done with Check Home Assistant Configuration add-on. If you don’t have it please first install as shown in the video.

From the left menu go to Supervisor. Select tab Add-on Store. Search for Check Home Assistant configuration. It is an official add-on. Click INSTALL.

After successful installation, click START. Go to tab Log, periodically click the REFRESH button and observe the log output. On Raspberry Pi the check takes about 10 minutes so don’t hold your breath and patiently wait the check to finish. If there are no errors proceed to the next step.

Step 4: Apply an update for the operating system if such is available. From the left menu go to Supervisor. Click UPDATE.

The Home Assistant Operating System is a minimal image that runs containers and comes with Supervisor to manage Home Assistant Core and add-ons. Once you hit the update button in the web interface, depending on your system and Internet connection speed, it will take a while until the update downloads and installs. Just wait patiently. As part of the update Home Assistant will restart so you will temporary lose connection to it.

Step 5: Update Home Assistant Core. After ensuring that you are running the latest stable version of Home Assistant Operating System proceed with updating Home Assistant Core. From the web interface hit the update button and patiently wait. It will again take a while depending on your system’s hardware and Internet connection. As part of the update Home Assistant will restart so you will temporary lose connection to it. After that you will be asked to login again. Congratulations, this the whole update procedure from the user interface. As promised is straight-forward and easy!

One more thing, if are an advanced user and for one reason or another you don’t like graphical user interfaces, it is also possible to update Home Assistant through the command-line interface. Just run in a terminal: ha core update.

If you have any questions or feedback please leave a comment. Subscribe to my YouTube channel and have a look at the open source hardware we offer.

ANAVI Macro Pad 8 Kits Are In Stock at Crowd Supply and Mouser

Recently we shipped ANAVI Macro Pad 8 kits to Crowd Supply warehouse. Crowd Supply team will start shipping them to you soon to backers of the crowdfunding campaign. Furthermore kits will be available on sale at both Crowd Supply and Mouser.

A fully loaded courier truck with huge quantity of ANAVI Macro Pad 8 kits travelling to the warehouse

ANAVI Macro Pad 8 is an open source, custom-programmable, mini 8-key mechanical keyboard. Fully compatible and running the popular Quantum Mechanical Keyboard (QMK) open source firmware.

ANAVI Macro Pad 8 – the open source hardware 8% (8-key) mechanical keyboard

ANAVI Macro Pad 8 is made in Plovdiv, Bulgaria, EU. Here we write with a Cyrillic alphabet so if you are wondering what is the strange looking text on the parcel’s red labels – it is the word for fragile in Bulgarian 🙂

Fragile in both English and Bulgarian

Keep in mind ANAVI Macro Pad 8 is indeed fragile and please be gentle with the mini OLED display while assembling your kit.

USB to microUSB cable is not included in any of the kits. Pick a cable that suits you best or recycle a cable, for example from an old smartphone. Please be careful when plugging the cable and make sure it doesn’t bend as this may damage the microUSB connector on ANAVI Macro Pad 8.

Huge thanks to all people who supported the project by placing an order during the crowdfunding period at Crowd Supply. If you missed the crowdfunding campaign you can still order ANAVI Macro Pad 8 from our distributors right now!

Integrating ESPHome Device to Home Assistant

ESPHome is an open source firmware for your ESP8266 or ESP32 devices with simple and yet powerful configuration files that allows you to control them remotely through the open source IoT platform Home Assistant and/or other home automation systems.

In this tutorial you will learn how to add a device with ESPHome in Home Assistant. The open source hardware ANAVI Light Controller with 12V RGB LED strip is used for the demonstration.

Upload ESPHome

You can either do this through the command line or alternatively, you can do it through Home Assistant ESPHome add-on.

Depending on the device you may need to edit an existing ESPHome configuration file or to create new from scratch. An example for ANAVI Light Controller is available at GitHub. Remember to set your WiFi credentials and device password in it as well as to enable the API. After flashing ESPHome to the device it is important to write down the address and the port. Both are printed in the serial output after booting the device.

After flashing ESPHome to the device it is important to write down the address and the port. Both are printed in the serial output after booting the device.

Home Assistant Integration

Open the web interface of Home Assistant. From the left side menu select Configuration and after that click Integrations. Click the button in the right lower corner with label Add Integration. From the menu select ESPHome. Enter connection settings for your ESPHome device. Set the address for host and port both of which were obtained on the first step. Click SUBMIT. Enter the password from the ESPHome configuration file. Click FINISH to complete adding the device.

After successfully adding the ESPHome device to Home Assistant it will appear in the overview section. For more details have a look at the video.

ANAVI Light Controller and 12V RGB LED strip controlled with ESPHome and Home Assistant from mobile application on Android smartphone

Select Language in Home Assistant

Select language in Home Assistant

Home Assistant is an advanced open source IoT and home automation platform. The user-friendly web user interface supports multiple languages.

  1. Open a web browser and log into Home Assistant.
  2. Go to you user profile by clicking your user account initials at the bottom of the sidebar.
  3. Select a language from the drop-down menu.
  4. The new language will be applied immediately.

Out of the box Home Assistant supports multiple languages including English, Spanish, French, German, Russian and many more. Home Assistant is an open source project and this allows adding translations and support for more languages in future.

ANAVI Macro Pad 8 Manufacturing Progress

ANAVI Macro Pad 8 is an open source, programmable, eight-key keypad with backlighting, underlighting, and OLED screen. Following the successful crowdfunding campaign we manufactured the printed circuit boards in a small local factory in Plovdiv, Bulgaria, EU. We would like to explain in detail the whole manufacturing process.

The fabrication includes a procedure called panelization which groups together a number of PCBs on a larger board called a “panel”. In the case of ANAVI Macro Pad 8 the “panel” contains 3 boards. All of them are gold plated through electrolytic nickel-gold process. Gold is very expensive, especially at the moment, but it is still worth it. Gold-plated PCBs have excellent quality with high hardness, wear and oxidation resistance.

A panel with 3 printed circuit boards for ANAVI Macro Pad 8

Sourcing parts in the COVID-19 time is a challenge but we work with trusted and reliable suppliers. We bought Microchip ATmega32U4 microcontrollers from Mouser. They arrived from the warehouse in Texas, USA. Each microcontroller is with TQFP-44 package that requires surface mount technology (SMT). The local factory has already assembled them alongside with all other SMT components.

The assembly of Gateron red mechanical switches and the red 3mm LEDs for all developer kits requires through-hole technology, a.k.a. manual soldering. This is a time consuming process. To simplify the work and to keep the mechanical switches on their places we created this plate that matches the size of the panels.

There are special holes on each mechanical switch for the 3mm LED. After soldering all of them, the leads of the LEDs have to be cut from the back side of the panel.

After all these steps, testing and packaging the developer kit will not require any soldering. However, people who enjoy soldering like me can order a maker kit and experiment with various mechanical switches and 3mm LEDs with different colors. Furthermore, the maker kit allows to perform a hot-swap upgrade as explained in the previous post.

After burning a the same bootloader as in Arduino Leonardo, flashing the open source QMK firmware and testing our mechanical keyboards are ready for packaging!

ANAVI Macro Pad 8 Developer Kit
ANAVI Macro Pad 8 Maker Kit

How to Make Hot-Swappable Mechanical keyboard PCB?

Hot-swappable mechanical keyboard allows you to replace switches and LEDs on the go without soldering and without even powering off the keyboard. In this short video tutorial I explain how to make hot-swappable any printed circuit board for a mechanical keyboard with footprints for Cherry MX plate switches. Other brands such as Gateron and Kaihl are compatible with the Cherry MX switches so this solutions is universal.

Hot-Swappable Sockets for DIY Mechanical Keyboard

The video has been created with a maker kit of the open source mechanical keypad ANAVI Macro Pad 8. I have customized it by adding holtite sockets to make it hot-swappable.

Required Hardware

ANAVI Macro Pad 8 with holtite sockets for hot-swap of Cherry MX and Gategron mechanical switches

Step 1


Using the tweezers place the holtite sockets into the PCB. The sockets are small so be careful not to lose any of them. Turn on the soldering iron. Heat each socket and gently push it. So we are using a soldering iron but in this case not for soldering. We are just mounting the sockets using its heat.

It looks easier than it is. It took me some time to do it for all switches and LEDs. Each key has 2 holes for the switch and 2 holes for the LED so basically you need 4 sockets with appropriate sizes for each key.

Step 2

Next step is optional and specific for ANAVI Macro Pad 8. The maker kit includes WS2812B addressable LED strip which should be soldered on the back of side of the keyboard. Please note the arrow that indicates the direction of the LED strip and make sure you are placing it properly as shown in the video.

Step 3

Cut the legs of the 3mm LEDs to make sure they will fit well in the hot-swappable holtite sockets that we have already mounted.

Step 4

Assemble the switches, the LEDs and the key caps. Once you are done with steps 1 this is easy because you already have a hot-swappable printed circuit board for your mechanical keyboard.

Custom ANAVI Macro Pad 8 with blue Cherry MX switches and green 3mm LEDs for backlit

By default ANAVI Macro Pad 8 is with Gateron red switches, red LEDs and white translucent keycaps. However, in this case with the hot-swappable version I am experimenting primary with blue Cherry MX switches, green LEDs and dark translucent keycaps. I have purchased several different mechanical switches: Gateron Red, Cherry MX blue and Cherry MX brown. Please note that these particular Cherry MX brown switches in the video do not have slots for the 3mm LEDs.

Although in this video I am using the maker kit of ANAVI Macro Pad 8. The same approach with holtite sockets can be applied on any other PCB for mechanical keyboard with footprint for Cherry MX switches.

“Spiderman” Raspberry Pi with ANAVI Infrared pHAT

Jesús Figueres, a data scientist interested in artificial intelligence (AI), shared in Twitter his setup of Raspberry Pi and ANAVI Infrared pHAT. It is living upside down on his lab’s ceiling so he calls it “Spiderman”. No doubt this is a suitable name in this case!

Jesús has attached various sensors for collecting data as we as a Raspberry Pi camera to take pictures of the room. He has developed energy efficiency algorithms running in the cloud which make decisions based on the data from the sensor and after that ANAVI Infrared pHAT takes care for transmitting commands as a stream of infrared signals to his air conditioner.

ANAVI Infrared pHAT
ANAVI Infrared pHAT

ANAVI Infrared pHAT is a low-cost open source hardware add-on board for Raspberry Pi with infrared receiver and transmitted. Furthermore it has slots for attaching up to 3 I2C sensor modules as well as convenient UART pins. We launched it in 2017 and it is one of our best-selling products. ANAVI Infrared pHAT is available at our distributors around the world and you can order it to build a similar home automation solution.