Tag: WS2811

Holiday Lights with Home Assistant, ANAVI Miracle Controller, and Olimex WS2811 LED Ropes

This YouTube video demonstrates do-it-yourself (DIY) holiday lights to celebrate Christmas or Halloween using ANAVI Miracle Controller, Olimex WS2811 LED ropes and the popular open source home automation platform Home Assistant!

ANAVI Miracle Controller and Olimex LED-Ropes-10 managed from Home Assistant app for Android

All kits of ANAVI Miracle Controller come with WS2812B LED strip, however the board is also compatible with other addressable LED strips. In a previous update we covered Adafruit NeoPixels and now we are focussed on Olimex WS2811 LED Rope.

ANAVI Miracle Controller with mini OLED display and a couple of Olimex LED-ROPE-10

Required Hardware

  • ANAVI Miracle Controller
  • 5V power supply
  • Two Olimex LED-ROPE-10
  • Raspberry Pi (recommended 3 or newer) with Home Assistant

Olimex is a well-known company in the maker community and I am lucky because their headquarter is my hometown Plovdiv, Bulgaria.

Olimex offers addressable, water proof, sealed with resin RGB WS2811 ropes with various number of LEDs. For this video I used a couple of Olimex LED-ROPE-10. The rope is waterproof so it is suitable for both indoor and outdoor installations. It works with power supply in the range from 3.3V to 5.5V and has a dedicated WS2811 driver for each LED.

The typical color code for Olimex LED-ROPE-10:

  • Olimex rope RED wire – VCC (3.3V-5.5V)
  • Olimex rope GREEN/BLUE (varies) wire – GND
  • Olimex rope WHITE wire – DATA

Each RGB LED in Olimex rope draws approximately 50mA at 5V with red, green, and blue at full brightness. Olimex LED-ROPE-10 has only 10 RGB LEDs with makes approximately 500mA and it is OK to power it through ANAVI Miracle Controller. For installation will longer ropes with bigger consumption wire the VCC and GND lines directly to the power supply.

When using Olimex LED ropes, set ANAVI Miracle Controller to 5V input and use an appropriate 5V center positive power supply!

For Olimex LED-Ropes-10 set ANAVI Miracle Controller to 5V and use appropriate 5V power supply
Wiring of a couple of Olimex LED-ROPE-10 to ANAVI Miracle Controller

NOTE: The color codes of other addressable LED strips, including WS2812B LED strip from all kits, are different!

Due to differences in color codes this wiring is valid only for Olimex LED ropes. Be careful and check the proper wiring as well input voltage requirements if you are using a different type of addressable LED strip or rope.

Software

Home Assistant must be installed on an appropriate device. If you haven’t installed it already, a single board computer like Raspberry Pi (version 3 or newer) is the perfect fit!

MQTT broker is also required and must be installed. You can install Mosquitto from Home Assistant add-on store. Integrate the MQTT broker in Home Assistant and enable discovery. The exact steps have been covered in a previous blog post about ANAVI Miracle Controller and Adafruit NeoPixels.

Please, ensure you are running the latest version of the open source firmware for ANAVI Miracle Controller. It is available at GitHub. You can flash it through Arduino IDE following these steps.

After completing the initial installation and integration in Home Assistant, you can easily control the holiday lights from your personal computer, smartphone or tablet. You can either install the official mobile app on your smartphone or use the web interface from any modern HTML5 web browser (Google Chrome, Mozilla Firefox, etc). Furthermore, with Home Assistant you can create automation and trigger automatically the holiday lights depending on various events.

You may also like

ANAVI Miracle Controller Successfully Crowdfunded!

Hip hip hooray! The crowdfunding campaign of ANAVI Miracle Controller at Crowd Supply was successful. It ended on 5 February 2020. We met all stretch goals.

ANAVI Miracle Controller is an ESP8266-powered Wi-Fi dev board to control two 5 V or two 12 V addressable (digital) LED strips like WS2812B, WS2812, WS2811, etc. Furthermore, mini OLED display and up to 3 I2C sensors can be attached. It has been certified by the Open Source Hardware Association.

We have already started manufacturing. The first and second batches of boards are ready. Right now we are testing and packaging them. The estimated shipping date remains the same – Mar 30, 2020. In the meantime you can still place pre-orders at the same prices. Crowd Supply will take care of the shipping for all orders placed during the crowdfunding campaign and pre-orders.

You may also like

Flashing Firmware on ANAVI Miracle Controller with Arduino IDE

ANAVI Miracle Controller is a new entirely open source development board for addressable (digital) LED strips like NeoPixels, WS2812B, WS2811, etc. The major advantages are that you can control two LED strips simultaneously, add a mini OLED display and I2C sensor modules as peripherals. Recently we launched a crowdfunding campaign for it at Crowd Supply.

ANAVI Miracle Controller

ANAVI Miracle Controller is a development board and it is easy to flash a custom firmware on it. The process is very similar as for our other open source project like ANAVI Thermometer, ANAVI Gas Detector and ANAVI Light Controller.

This tutorial explains the exact steps how to compile and upload the default open source Arduino sketch for ANAVI Miracle Controller using Arduino IDE.

Required Hardware

  • ANAVI Miracle Controller
  • USB to UART debug cable
  • Addressable LED strip
  • Appropriate power supply at 5V or 12V depending on the type of LED strips
  • Personal computer with MS Widows, Mac OS or GNU/Linux distribution
  • Optionally a mini OLED display and other peripherals can be attached
ANAVI Miracle Developer kit

Download Source Code from GitHub

The default firmware of ANAVI Miracle Controller is an open source Arduino sketch. It relies on several popular open source Arduino libraries, including FastLED for controlling addressable LED strips. Clone or download the source code from GitHub.

Connecting UART to USB

Each ANAVI Miracle Controller kit includes a USB to UART debug cable with CP2102. Depending on the operating system on your PC you might be required to install additional drives. It works out of the box on GNU/Linux distributions. As open source enthusiasts we are using it on Ubuntu. Plug the USB in your computer and connect the 3 wires as follows:

ANAVI Miracle ControllerUSB to UART Debug Cable
RXTX
TXRX
GNDGND
Connecting USB to UART cable to ANAVI Miracle Controller

Download Arduino IDE

Download and install Arduino IDE on your personal computer. It is free and open source software available for MS Windows, Mac OS and GNU/Linux distributions.

Launch Arduino IDE. From File > Open load an Arduino sketch. It can be the default firmware or any other compatible with ANAVI Miracle Controller Arduino sketch.

Configure ESP8266 in Arduino IDE

Go to File > Preferences. Select Settings and in the field Additional Boards Manager URLs add: http://arduino.esp8266.com/stable/package_esp8266com_index.json

From Arduino IDE select Tools > Board: Generic ESP8266 Module. Set the flash size to 4M (1M SPIFFS). The upload speed is 115200. Adjust the exact port of USB to serial debug cable connected to your computer.

Install Libraries

Select Tools > Manage Libraries. The Arduino library manager will appear. Install all required libraries and their exact versions. Over the time, with the development of the default firmware, new libraries might be added. Please have a look at the README file to get the up to date list of all Arduino libraries on which the the default firmware depends on.

Compile & Upload

In Arduino IDE click Verify/Compile. If there are any errors, please double check that you have installed all required libraries and their exact versions. If the source code compiles successfully, please proceed to to the next step for flashing the firmware.

Set the jumper to 5V or 12V depending on the type of addressable LED strip and power supply. Mismatch of the voltage may lead to severe hardware failure.

In Arduino IDE click Upload. Set the jumper on ANAVI Miracle Controller to 5V or 12V depending on your power supply and type of LED strips. The power supply voltage must match the required voltage by the LED strips, for example 5V for NeoPixels and the WS2812B included in all kits. Press and hold the RESET button on ANAVI Miracle Controller. Without releasing the RESET button, plug the power supply in the barrel jack of ANAVI Miracle Controller.

Do NOT release the RESET button until you see in Arduino IDE that the upload is 100% completed!

ANAVI Miracle Controller with 2 WS2812B LED strips connected to a laptop using USB to UART cable

You may also like

ANAVI Miracle Controller

ANAVI Miracle Controller is an open source hardware Wi-Fi development board powered by the ESP8266 and designed to control two 5 V or 12 V addressable LED strips simultaneously.

ANAVI Miracle Controller supports popular addressable LEDs including Neopixel, WS2811, WS2812B, TM1809, etc. It also has a dedicated slot for a mini OLED I²C display and slots for up to three additional I²C sensor modules. The default firmware is available at GitHub as an Arduino sketch implementing Home Assistant MQTT Light component.

Back in 2018 we created ANAVI Light Controller for low-cost 12V RGB LED strips. Inspired by a lot of people asking for open source hardware dev board for addressable LEDs strips we created ANAVI Miracle Controller.

Last week we launched a crowdfunding campaign for ANAVI Miracle Controller at Crowd Supply. Learn all the details here. We are ready for manufacturing and now we need your support. We hope you help us bring this entirely open source project to life!

You may also like